Australian Terrier Grooming Revisited
By: Theresa A.Goiffon
NEW! Visit my new grooming video and see the technique and tools I use to groom my dogs. Here is the link.
I would like to preface this with, I am by no means an expert groomer. I have learned to groom my Australian Terrier on my own. However, over the past couple years, I have also had the privilege to have a few experienced Australian Terrier Breeders and Handlers show me a few tips as well.
This blog was created because of the many inquires I receive regarding grooming and to update my previous blog Grooming your Australian Terrier 101. I share with you what I have learned about grooming, over the past 5 years, and what has worked best for me.
The best way to groom your Australian Terrier, is to maintain the coat and strip away the overgrown hair. The dead hair is painlessly pulled from the dog's skin, providing a place for their new hair growth to keep their coat hardened.
The best tools to complete this task besides hand stripping with your own finger tips are as follows:
Stripping Stone or Pumice Stone Sticks
Pin Brush and Metal Comb
Toe Nail Clipper
Rubber Tips (for your fingers)
Terrier Chalk (white powder sprinkle about 15 min prior to stripping)
Your Australian Terrier needs a bath only 3-4 times a year, or if he is exceptionally dirty.
He should be brushed every week. A pin brush for the body, bristle brush for the face.
Always, strip in the direction of the hairs natural growth, never against.
Technique for stripping:
Brush your dog and remove any knots, pay close attention to the under arm area, the fine longer hair tends to get snarled in that area.
If you are using your fingers, brush the top coat forward, just a bit to see the longer hairs standing up. Pull those longer hairs in the direction of the hair growth or toward the tail. Repeat over the entire top and sides of the dog. If using a stripping knife of stone, place it in your hand similar to a way you might peel an apple. Keep the knife level, don't angle it toward their skin.
Comb over the top hair grasping the longer hair between the comb and your thumb and pull again, in the direction of the hair growth, or toward the tail. Do not go deep into the undercoat. If you have a bulky undercoat, you can simply comb down into the undercoat with the stripping knife to remove some of the bulk.
The feathery hair around his feet should be trimmed, and his tail and ears neatened. Until you are comfortable with using scissors around their ears, use a small dog electric shaver for their ears. Shave around the shape of the ears and shave the entire back of the ear in the direction of the hair growth, not against it. It’s not correct for showing, however, it is easy and safe if you are new to grooming and in 2 weeks, you achieve the look you want.
I strip the hair on the back of their ear and use a stripping stone to smooth out the back of the ear. Make these sessions, short and happy, and do a little at a time.
Eyes should be cleaned. Check that the nails are not too long, if you do not like to trim nails your vet will be happy to do it for you. Check that his ears are clean (don’t use q-tips) and also under his tail.
Grooming for a Show of if you want your dog to look its best:
Your breeder should give you a demonstration of show presentation if you require it. This is best done by practical demonstration, although looking at photos can help.
Top Knot: (The longer, silky hair on the top of the head)
Should be brushed forward to stand upright, but not hang in their eyes.
Ears: Short and kept free of long hair.
Ruff: (The collar, longer hair that stands out from the neck)
Brush forward and outwards. Ruff should not be cut.
Apron: (Longer hair under the neck and on the front section of the chest)
Brushed down and encouraged to grow.
Feet: Trimmed between pads, top of feet to be stripped and cat-like.
Body Coat: Brush down carefully untangle knots and knots that form on
stomach and arm pit areas.
Eyes: Keep the hair short and plucked around eye area
Neck: Brush and groom so that the neck appears long and arched.
Tail: (Envision the shape of a carrot, from tip being the point to the body being the thicker part)
Remove all long hairs from tail, both around the tail and behind it. So that the tail appears natural, straight and set on high. Thinning scissors may be used to reduce the bulk of the tail.
Hindquarters: For cleanliness, keep hair short around the vent and in
case of males, around the prepuce.
Elbows: Shorten or brush down any hair at elbow which makes your dog
look out at elbows. Sometimes it may be necessary to thin hair slightly.
Muzzle: Should be free from long hair.
The beard under the muzzle should be trimmed neatly with scissors to the
shape of the muzzle, but not too severely.
Some general questions:
What is rolling a coat?
Rolling is removing the old layers of coat to make room for new growth. You can strip off the longest hair. This is done by pulling only about the longest third of the coat, leaving the rest for a week to two weeks depending on the dog, and then repeating until there is always new coat coming in underneath.
Is Knife or 'hands only' stripping better?
If a stripping knife is used properly, it works as well as pulling the coat only with fingers. For some, it's easier and quicker, certainly less work on your fingers. Despite the name 'knife,' it is not used to cut the hair, only to help grip it.
Looking at Australian Terrier photos can help you visualize the proper look. I hope this helps you. If you have other questions, please never hesitate to call or email me.
There is a grooming CD available for sale at www.AustralianTerrierInternational.org. I recommend it.
In : Breed Information
Tags: grooming australian terrier stripping your dogs coat